New Mercedes Benz WIFI MB SD Connect Compact 5 diagnostic tool for cars and trucks with/without software are available in mbstartool.com.
Top features of the new MB SD C5
1. Support wifi
2. Supported Multi-Language: English/Bulgarian/Danish/Greek/Spanish/French/Italian/Korean/Polish/Romanuan/Serbo-Croatian/
Turkish/Czech/German/Finish/Hyngarian/Japanese/Dutch/Portuguese/Russian/Swedish/Chinese
3. Supports Mercedes Benz Cars & Trucks 2000 up
4. Supports Offline and Online Programming, If You Want to Do Online, Please Buy This Online SCN Coding Service
Software includes: (Version: 2015.12)
1. D-A-S / Xentry 2015.12 : the automatically Diagnosis Assistance
System ,Concise interface and straightforward operation with IB M
high-quality computer can realize the quick and accurate code reading
and the whole car system testing
2. W-I-S net 2015.12: Workshop Information System Supply the whole view
of the wiring diagram in a car,component location diagram and
maintenance method. What you do is to enter the chassis number, and then
you will get the manufacture data, engine configuration and the car
model -all in detail.
3. EPC.net : Electronic Parts Catalog
4. ST Finder 2008:Part location finder
5. STARUTILITIES : the movement management system and self-test
6, SDMEDIA 2014
7, PL69
Tuesday, October 15, 2019
Tuesday, October 8, 2019
MB SD Connect C4/C5 Star Diagnosis tool cannot measure the car
The customer connected the Mercedes-Benz to be tested, opened the MB SD Connect C4/C5 xentry software, and selected the corresponding model. The final step of the test is as follows:
The above problem occurred and the hardware of MB SD Connect C4/C5 was not found. Generally there are three problems:
1. MB SD Connect C4/C5 host problem
2. MB SD Connect C4/C5 network cable problem
3. Computer problem with MB SD Connect C4/C5
The customer connects to the host and computer of the MB SD Connect C5/C4 via a network cable. The host’s MB SD Connect C4/C5 host screen is displayed as follows:
From the display prompt: Device not in use
As you can see, MB SD Connect C4/C5 does not work.
Look at the icon in the red circle: This display is the MB SD Connect C4/C5 host is not connected to the computer.
If the MB SD Connect C4/C5 host is connected to the computer, the icon should look like this:
That may be because
1, network cable problem
2, the network card is broken
3, the network card driver has a problem
Solution:Replace a new network cable (common with ordinary network cable)
1. If you replace the new network cable and the connection is normal as shown below, the original network cable is damaged.
2. If you change the network cable or the following is displayed: that is, the computer’s network card or network card driver has a problem.
3. If it is a driver problem, reinstall the NIC driver to solve it.
4. If the NIC driver is reinstalled, the problem remains the same. That is the problem with the network card, please check or replace the new network card to solve.
At the same time, if your MB SD Connect C4/C5 hardware can be connected to the car, the lower right corner of your computer will display as follows:
If the MB SD Connect C4/C5 hardware is not connected to the car and computer, or if the hardware is not found after the connection, it will be displayed as follows:
If you still have problem to use MB SD Connect C4/C5 Star Diagnostic tool, please contact our sales.
The above problem occurred and the hardware of MB SD Connect C4/C5 was not found. Generally there are three problems:
1. MB SD Connect C4/C5 host problem
2. MB SD Connect C4/C5 network cable problem
3. Computer problem with MB SD Connect C4/C5
The customer connects to the host and computer of the MB SD Connect C5/C4 via a network cable. The host’s MB SD Connect C4/C5 host screen is displayed as follows:
From the display prompt: Device not in use
As you can see, MB SD Connect C4/C5 does not work.
Look at the icon in the red circle: This display is the MB SD Connect C4/C5 host is not connected to the computer.
If the MB SD Connect C4/C5 host is connected to the computer, the icon should look like this:
That may be because
1, network cable problem
2, the network card is broken
3, the network card driver has a problem
Solution:Replace a new network cable (common with ordinary network cable)
1. If you replace the new network cable and the connection is normal as shown below, the original network cable is damaged.
2. If you change the network cable or the following is displayed: that is, the computer’s network card or network card driver has a problem.
3. If it is a driver problem, reinstall the NIC driver to solve it.
4. If the NIC driver is reinstalled, the problem remains the same. That is the problem with the network card, please check or replace the new network card to solve.
At the same time, if your MB SD Connect C4/C5 hardware can be connected to the car, the lower right corner of your computer will display as follows:
If the MB SD Connect C4/C5 hardware is not connected to the car and computer, or if the hardware is not found after the connection, it will be displayed as follows:
If you still have problem to use MB SD Connect C4/C5 Star Diagnostic tool, please contact our sales.
Thursday, September 26, 2019
MB Star C6 Benz Diagnostic Tool with DOIP&AUDIO Function
VXDIAG MB SD Connect C6 MB Star C6 Benz Diagnostic Tool with DOIP&AUDIO Function Better than MB STAR C4/C5
Original VXDIAG For XENTRY Diagnosis VCI VXDIAG For XENTRY Diagnosis DoIP Pass Through Interface
VXDIAG For XENTRY Diagnosis VCI is the latest interface for For Mercedes & SMART vehiclescan replace Star C4/C5. VXDIAG For XENTRY Diagnosis VCI acts as a Pass-through Interface, also called Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the VXDIAG For XENTRY software loaded on a PC. CnAutotool.com VXDIAG MB Star C6 Multiplexer MB SD Connect C6 Benz Diagnostic ToolWith DOIP Functions And V2018.12 MB Star C6 Download Software.
VXDIAG MB SD Connect C6 XENTRY Diagnosis VCI Features:
1. VXDIAG For XENTRY Diagnosis VCI can be used for all model series of For Mercedes For Benz vehicles
2. VXDIAG For XENTRY Diagnosis VCI support DoIP, cover more functions during SCN Coding than SD C4/C5
3. VXDIAG For XENTRY Diagnosis VCI functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
4. VXDIAG For XENTRY Diagnosis VCI Diagnosis updates no longer necessary – firmware updates required on rare occasions
5. VXDIAG For XENTRY Diagnosis VCI does not need a power supply unit for external power supply
6. VXDIAG For XENTRY Diagnosis VCI Handy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
7. Engines (All Gasoline & Diesel Systems)
8. Transmissions and Electronic Selector Modules
9. Airmatic and Active Body Control Suspension Systems
10. Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
11. Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
12. Drive Authorisation System
13. Sam (Signal Acquisition) Modules
14. Electronic Ignition System (EIS)
15. Pneumatic System Equipment and ATA functions
16. Air Conditioning / climate control Systems
17. Instrument Cluster
18. Tyre Pressure Control
19. Parktronic System
20. Keyless Go
21. D2b Command & Audio Gateway (D2B and MOST networks)
22. TV Tuner
23. Headlamp Range Adjustment
24. Seat Electronics
25. Rvc, RST & Vario Roof modules
26. Automatic Clutch System ACS
27. M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
28. Assyst & ASSYST + systems
Original VXDIAG For XENTRY Diagnosis VCI VXDIAG For XENTRY Diagnosis DoIP Pass Through Interface
VXDIAG For XENTRY Diagnosis VCI is the latest interface for For Mercedes & SMART vehiclescan replace Star C4/C5. VXDIAG For XENTRY Diagnosis VCI acts as a Pass-through Interface, also called Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the VXDIAG For XENTRY software loaded on a PC. CnAutotool.com VXDIAG MB Star C6 Multiplexer MB SD Connect C6 Benz Diagnostic ToolWith DOIP Functions And V2018.12 MB Star C6 Download Software.
VXDIAG MB SD Connect C6 XENTRY Diagnosis VCI Features:
1. VXDIAG For XENTRY Diagnosis VCI can be used for all model series of For Mercedes For Benz vehicles
2. VXDIAG For XENTRY Diagnosis VCI support DoIP, cover more functions during SCN Coding than SD C4/C5
3. VXDIAG For XENTRY Diagnosis VCI functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
4. VXDIAG For XENTRY Diagnosis VCI Diagnosis updates no longer necessary – firmware updates required on rare occasions
5. VXDIAG For XENTRY Diagnosis VCI does not need a power supply unit for external power supply
6. VXDIAG For XENTRY Diagnosis VCI Handy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
7. Engines (All Gasoline & Diesel Systems)
8. Transmissions and Electronic Selector Modules
9. Airmatic and Active Body Control Suspension Systems
10. Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
11. Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
12. Drive Authorisation System
13. Sam (Signal Acquisition) Modules
14. Electronic Ignition System (EIS)
15. Pneumatic System Equipment and ATA functions
16. Air Conditioning / climate control Systems
17. Instrument Cluster
18. Tyre Pressure Control
19. Parktronic System
20. Keyless Go
21. D2b Command & Audio Gateway (D2B and MOST networks)
22. TV Tuner
23. Headlamp Range Adjustment
24. Seat Electronics
25. Rvc, RST & Vario Roof modules
26. Automatic Clutch System ACS
27. M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
28. Assyst & ASSYST + systems
Wednesday, September 25, 2019
V2017.9 Original Software Mercedes Benz MB SD C5 SD Connect Compact 5 Star Diagnosis with Engineer
Benz c5 can provide complete diagnosis for the newest hybrid W222.
And it has a qualitative improvement in hardware and software by
authorization of diagnostic interface to control the software.can work
on windows xp, win7/8/10 system.
Xentry Connect C5 Benz SD Connect DoIP Wifi MB Star C5 Xentry Tab Kit Diagnosis Multiplexer
Benz c5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
The tool we sell do not include the xentry tab, you can equip one yourself or choose other laptop, it is just as a display, no special requirement.
Xentry Connect (VCI+) Technical Parameters:
1.OS: Windows Embedded Standard 7(32bit)
2.Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
3.Memory: 4G hard disk with 256GB SSD
4.Display: 128*64 PX
5.Battery: 40 minutes (When CPU capacity to 60%)
6.Weight: 1.9KG
7.Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
The way to connect: support wireless connection via 1000M workshop switches, also support wired connection.
What the difference on diagnostic systems based on Xentry Connect from other equipment used to diagnose Mercedes cars?
What are its distinguishing features?
Hardware, despite the similarity of many solutions with multiplexers SD Connect –
but the different All diagnostic software is loaded into the Xentry Connect multiplexer itself.
The management software can be installed on any computer with Windows 7 – 32-bit or Windows 8 – 32-bit and serves only for communication with the multiplexer
The licensing system is reworked – now licenses are stored on MB servers – Any license changes are tracked by the multiplexer when connected to the Internet network.
Why should buy Xentry connect
After 2015, all Star Diagnosis equipment is no longer supported. First of all, this means that there is no update of the diagnostic data for the newest cars and their systems, as well as the lack of the possibility of coding and programming of electronic units due to the backlog of the software data level in the device, from data in the electronic control units of the car.
Already at the end of 2014, at most dealerships, almost all of the previously used Star Diagnosis Compact4 with SD Connect DoIP multiplexers were almost completely removed. Instead, dealers received Xentry Kit kits, which include the latest Xentry Connect multiplexers and Xentry Tab tablets from Panasonic. Tablets are custom-made, although they also have a “civilian” version – the Panasonic Toughbook CF-D1,
somewhat inferior in terms of battery life to the original Xentry Tab, but it has a much more powerful configuration.
Honestly, the need to use the Xentry Tab on non-dealer services seems somewhat exaggerated to me. With dealers everything is clear – they were forced to use this equipment.
And what about workshop service? Undoubtedly, the tablet from Panasonic is not very bad … But … Its price is disheartening. The cost of the Japanese tablet is realistic to buy pieces of eight new laptops or tablets from other manufacturers.
So , we suggest buy Xentry connect from us , then buy a laptop yourself . the software from which Xentry Connect is managed can be installed without any problems on any computer that has a 32-bit version of Windows 7, Windows 8 or Windows 10. It’s clear with Xentry Connect itself – there’s no alternative .
After all, in this choice there are many reasons that encourage one to make a decision. The main thing is one: since 2015, the diagnostic multiplexer Xentry Connect C5 becomes the only one used at dealerships.
Thus, by purchasing this equipment, you do not lag behind the progress. You use in your work the best that is available today. Each your client, seeing with his own eyes that you in your work use the same device that he saw at the dealer’s service station, will understand that he made the right decision entrusting his car to your specialists.
Xentry Connect C5 Benz SD Connect DoIP Wifi MB Star C5 Xentry Tab Kit Diagnosis Multiplexer
Benz c5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
The tool we sell do not include the xentry tab, you can equip one yourself or choose other laptop, it is just as a display, no special requirement.
Xentry Connect (VCI+) Technical Parameters:
1.OS: Windows Embedded Standard 7(32bit)
2.Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
3.Memory: 4G hard disk with 256GB SSD
4.Display: 128*64 PX
5.Battery: 40 minutes (When CPU capacity to 60%)
6.Weight: 1.9KG
7.Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
The way to connect: support wireless connection via 1000M workshop switches, also support wired connection.
What the difference on diagnostic systems based on Xentry Connect from other equipment used to diagnose Mercedes cars?
What are its distinguishing features?
Hardware, despite the similarity of many solutions with multiplexers SD Connect –
but the different All diagnostic software is loaded into the Xentry Connect multiplexer itself.
The management software can be installed on any computer with Windows 7 – 32-bit or Windows 8 – 32-bit and serves only for communication with the multiplexer
The licensing system is reworked – now licenses are stored on MB servers – Any license changes are tracked by the multiplexer when connected to the Internet network.
Why should buy Xentry connect
After 2015, all Star Diagnosis equipment is no longer supported. First of all, this means that there is no update of the diagnostic data for the newest cars and their systems, as well as the lack of the possibility of coding and programming of electronic units due to the backlog of the software data level in the device, from data in the electronic control units of the car.
Already at the end of 2014, at most dealerships, almost all of the previously used Star Diagnosis Compact4 with SD Connect DoIP multiplexers were almost completely removed. Instead, dealers received Xentry Kit kits, which include the latest Xentry Connect multiplexers and Xentry Tab tablets from Panasonic. Tablets are custom-made, although they also have a “civilian” version – the Panasonic Toughbook CF-D1,
somewhat inferior in terms of battery life to the original Xentry Tab, but it has a much more powerful configuration.
Honestly, the need to use the Xentry Tab on non-dealer services seems somewhat exaggerated to me. With dealers everything is clear – they were forced to use this equipment.
And what about workshop service? Undoubtedly, the tablet from Panasonic is not very bad … But … Its price is disheartening. The cost of the Japanese tablet is realistic to buy pieces of eight new laptops or tablets from other manufacturers.
So , we suggest buy Xentry connect from us , then buy a laptop yourself . the software from which Xentry Connect is managed can be installed without any problems on any computer that has a 32-bit version of Windows 7, Windows 8 or Windows 10. It’s clear with Xentry Connect itself – there’s no alternative .
After all, in this choice there are many reasons that encourage one to make a decision. The main thing is one: since 2015, the diagnostic multiplexer Xentry Connect C5 becomes the only one used at dealerships.
Thus, by purchasing this equipment, you do not lag behind the progress. You use in your work the best that is available today. Each your client, seeing with his own eyes that you in your work use the same device that he saw at the dealer’s service station, will understand that he made the right decision entrusting his car to your specialists.
Friday, September 20, 2019
MB Star C6 Benz Diagnostic Tool with DOIP&AUDIO Function
VXDIAG MB SD Connect C6 MB Star C6 Benz Diagnostic Tool with DOIP&AUDIO Function Better than MB STAR C4/C5
Original VXDIAG For XENTRY Diagnosis VCI VXDIAG For XENTRY Diagnosis DoIP Pass Through Interface
VXDIAG For XENTRY Diagnosis VCI is the latest interface for For Mercedes & SMART vehiclescan replace Star C4/C5. VXDIAG For XENTRY Diagnosis VCI acts as a Pass-through Interface, also called Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the VXDIAG For XENTRY software loaded on a PC. CnAutotool.com VXDIAG MB Star C6 Multiplexer MB SD Connect C6 Benz Diagnostic ToolWith DOIP Functions And V2018.12 MB Star C6 Download Software.
VXDIAG MB SD Connect C6 XENTRY Diagnosis VCI Features:
1. VXDIAG For XENTRY Diagnosis VCI can be used for all model series of For Mercedes For Benz vehicles
2. VXDIAG For XENTRY Diagnosis VCI support DoIP, cover more functions during SCN Coding than SD C4/C5
3. VXDIAG For XENTRY Diagnosis VCI functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
4. VXDIAG For XENTRY Diagnosis VCI Diagnosis updates no longer necessary – firmware updates required on rare occasions
5. VXDIAG For XENTRY Diagnosis VCI does not need a power supply unit for external power supply
6. VXDIAG For XENTRY Diagnosis VCI Handy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
7. Engines (All Gasoline & Diesel Systems)
8. Transmissions and Electronic Selector Modules
9. Airmatic and Active Body Control Suspension Systems
10. Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
11. Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
12. Drive Authorisation System
13. Sam (Signal Acquisition) Modules
14. Electronic Ignition System (EIS)
15. Pneumatic System Equipment and ATA functions
16. Air Conditioning / climate control Systems
17. Instrument Cluster
18. Tyre Pressure Control
19. Parktronic System
20. Keyless Go
21. D2b Command & Audio Gateway (D2B and MOST networks)
22. TV Tuner
23. Headlamp Range Adjustment
24. Seat Electronics
25. Rvc, RST & Vario Roof modules
26. Automatic Clutch System ACS
27. M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
28. Assyst & ASSYST + systems
Original VXDIAG For XENTRY Diagnosis VCI VXDIAG For XENTRY Diagnosis DoIP Pass Through Interface
VXDIAG For XENTRY Diagnosis VCI is the latest interface for For Mercedes & SMART vehiclescan replace Star C4/C5. VXDIAG For XENTRY Diagnosis VCI acts as a Pass-through Interface, also called Star C6, For Benz C6 multiplexer to provide complete communication between a vehicle and the VXDIAG For XENTRY software loaded on a PC. CnAutotool.com VXDIAG MB Star C6 Multiplexer MB SD Connect C6 Benz Diagnostic ToolWith DOIP Functions And V2018.12 MB Star C6 Download Software.
VXDIAG MB SD Connect C6 XENTRY Diagnosis VCI Features:
1. VXDIAG For XENTRY Diagnosis VCI can be used for all model series of For Mercedes For Benz vehicles
2. VXDIAG For XENTRY Diagnosis VCI support DoIP, cover more functions during SCN Coding than SD C4/C5
3. VXDIAG For XENTRY Diagnosis VCI functions including diagnosing, programming, simulation studying, repair information, automotive maintenance, technical service bulletin and so on
4. VXDIAG For XENTRY Diagnosis VCI Diagnosis updates no longer necessary – firmware updates required on rare occasions
5. VXDIAG For XENTRY Diagnosis VCI does not need a power supply unit for external power supply
6. VXDIAG For XENTRY Diagnosis VCI Handy multiplexer with a small, sturdy construction (no PC core, battery, fan, or display)
7. Engines (All Gasoline & Diesel Systems)
8. Transmissions and Electronic Selector Modules
9. Airmatic and Active Body Control Suspension Systems
10. Traction Systems: ESP / ASR / ETS / ABS / BAS / SBC braking systems
11. Supplementary Restraint Systems (SRS) / Airbag, All body modules OCP / UCP / LCP / SCM / SKF / KFB / RCM / DCM’s
12. Drive Authorisation System
13. Sam (Signal Acquisition) Modules
14. Electronic Ignition System (EIS)
15. Pneumatic System Equipment and ATA functions
16. Air Conditioning / climate control Systems
17. Instrument Cluster
18. Tyre Pressure Control
19. Parktronic System
20. Keyless Go
21. D2b Command & Audio Gateway (D2B and MOST networks)
22. TV Tuner
23. Headlamp Range Adjustment
24. Seat Electronics
25. Rvc, RST & Vario Roof modules
26. Automatic Clutch System ACS
27. M-Class Body Modules (AAM / EAM / DAS / SEM / VG Transfer Case)
28. Assyst & ASSYST + systems
Wednesday, September 18, 2019
MB Star C5 Xentry Connect Mercedes Benz SD Connect C5 Enhanced than Mercedes sds C4 scanner
Benz Diagnostic Tool MB Star C5 Xentry Connect
is Mercedes Benz Star diagnosis mb c5. Given that the upgraded version
of Mercedes c4 multiplexer, the Mercedes Benz SD Connect C5 is
additionally a bit bit diverse. Autonumen MB Star C5 Xentry Connect
Mercedes Benz SD Connect C5 Enhanced than Mercedes sds C4 scanner.
In comparison towards the Mercedes c4 multiplexer, autonumen.com MB Star C5 Xentry Connect has been improved a lot, in order to stay away from some accidental problems which ordinarily occur to Mercedes sds C4 scanner for the duration of use. Like the crashes brought about by the overheat within the interface of your detection tool. Aside from that, other principal capabilities are frequently the identical with C4.
Autonumen is one of Mercedes program program for Star diagnosis, and outstanding for finishing up servicing and repair function. A number of MB proprietors get there at check with it continuously and also a number of wish to purchase it independently, but right here we autonumen.com provide you with it in the much more cost-effective usually means, specifically for Mercedes entrepreneurs. it might be autonumen.com MB Star C5 Xentry Connect, new solution for benz. some concerns folliwing might help lean a lot more about mb star c5.
Wifi MB SD Connect C5 from autonumen.com is latest wi-fi Mercedes BENZ Diagnostic Program mb sd connection c4 update model. Mercedes Star prognosis C5 multiplexer supports learning out & erasing trouble code,looking through the real-time data of sensor and actuator, coding and programming. Wifi MB SD Hyperlink compact 5 is MB SD Join C5 star diagnosis multiplexer. MB star C5 Xentry Link assistance Mercedes Benz Cars After Year 2000. WIFI MB sd hook up c5 mux from AUTONUMEN is the latest mercedes benz sd join compact 5 diagnostic instrument. MB SD Hook up C5 guidance K-line, can bus and usd protocols. MB sd hyperlink c5 aid Offline and Online Programming, If You Choose to Do Online, Please Buy Online SCN Coding Service.
In comparison towards the Mercedes c4 multiplexer, autonumen.com MB Star C5 Xentry Connect has been improved a lot, in order to stay away from some accidental problems which ordinarily occur to Mercedes sds C4 scanner for the duration of use. Like the crashes brought about by the overheat within the interface of your detection tool. Aside from that, other principal capabilities are frequently the identical with C4.
Autonumen is one of Mercedes program program for Star diagnosis, and outstanding for finishing up servicing and repair function. A number of MB proprietors get there at check with it continuously and also a number of wish to purchase it independently, but right here we autonumen.com provide you with it in the much more cost-effective usually means, specifically for Mercedes entrepreneurs. it might be autonumen.com MB Star C5 Xentry Connect, new solution for benz. some concerns folliwing might help lean a lot more about mb star c5.
Wifi MB SD Connect C5 from autonumen.com is latest wi-fi Mercedes BENZ Diagnostic Program mb sd connection c4 update model. Mercedes Star prognosis C5 multiplexer supports learning out & erasing trouble code,looking through the real-time data of sensor and actuator, coding and programming. Wifi MB SD Hyperlink compact 5 is MB SD Join C5 star diagnosis multiplexer. MB star C5 Xentry Link assistance Mercedes Benz Cars After Year 2000. WIFI MB sd hook up c5 mux from AUTONUMEN is the latest mercedes benz sd join compact 5 diagnostic instrument. MB SD Hook up C5 guidance K-line, can bus and usd protocols. MB sd hyperlink c5 aid Offline and Online Programming, If You Choose to Do Online, Please Buy Online SCN Coding Service.
Tuesday, September 3, 2019
How to Choose good SD C4 Star Diagnosis SDConnect MB Star C4
MHHAuto MB Star C4 Mercedes Benz Star Diagnosis SD Connect C4 Experience Sharing
There are so many kinds MB Star C4 SD Connect Multiplexer in the market, how to choose a good Star Diagnosis SD Connect Multiplexer? Below Autonumen.com share a Star Diagnostic SD Connect MB Star C4 Mux identify guide as following. This is sharing from MHHAuto forum, great Mercedes Star diagnostic SDconnect SD C4 tools experience sharing.
MHHAuto Thread: SD Connect C4 — avoiding garbage
I’m in the market for an SD connect C4 mercedes benz Star Diagnostic Tool and have been trying to spend my time doing some homework to avoid getting a garbage unit. I certainly can understand what a lot of people have been saying about the widely varying quality that’s out there. I am a EE and PCB designer, so I’m trying to make use of that knowledge to select the best unit that I can.
To that end, I’m going to share what info I’ve collected so far, and when I finally end up buying whatever unit I do, I’m going to do a full teardown on it and post the results here.
As another matter, I’ll openly post details on who I buy the unit from and impressions after receiving it.
Near as I can tell right now, there appear to be about 4 “factories” that make different units.
One thing I’ve been asking all of the sellers for (and I would encourage others to do the same) is photos of the actual MB Star C4 SD Connect unit (including PCBs) with a unique identifier in the photo to prove that the unit they say they are going to send me is the actual one they send me. Of course, some sellers immediately bail at this, but then you know who to avoid ahead of time.
In general, a lot of the components used in a Star diagnostic tool SD C4 Multiplexer are getting quite long in the tooth. Many of the parts are approaching 20 years of age. Thus, you stand a fair risk of getting pulls (used parts) and/or remarked parts on these.
In following posts, I’ll provide photos of what I can discern as differences between the MB Star Diagnostic SD Connect C4 units along with some commentary about whatever info I can provide at this point.
to, I’ve outlined some things I feel are important to note. They have a set of 4 analog switches on the PCB. In this photo, they are ADG426 from Analog Devices. I’ve seen some clones that use DG526CY from Harris/Intersil. The DG526CY, besides being completely obsolete, has an typical RDSON of 270 ohms vs 80 for the Analog Devices part. It also has a -55dB isolation vs -75dB for the AD part. In short, the AD part is just a much better mux. So with that said, I would insist on any unit I’m interested in using those.
A second thing you’ll notice is the use of can crystals where 4 pin variants were intended. This is just sloppy and cheap. There may also be issue with loading (and ultimately clock stability) depending on whether they matched the loading caps to the substituted crystal or not.
I haven’t had a set of photos high res enough to look at the rest of the actives in detail yet, as most sellers don’t seem to post them.
There’s also an issue pointed out on the bottom of the board where one of the (what appears to be) MOSFETs in (what appears to be a) D2 PAK looks like it was hand soldered. Again, no good.
This next photo is of the relay Star Diagnosis SD Connect PCB— I think one of the MHH members posted this from an original SD C4.
.5NU relays and EPCOS S513N chokes. I’ve seen plenty of PCBs where they remove the chokes and stub them out with 0 ohm resistors. That is a high crime in terms of signal integrity. You see a lot of “full chips” comments where these are present, although that is a bit of a misnomer. It should read as “common mode filters present”.
On this PCB, you’ll also notice the use of multilayer ceramic capacitors (MLCC) near the switching supplies. A lot of clones seem to use electrolytic capacitors in place of the bigger MLCCs because of the cost. MLCCs are preferred for switchers because of their low ESR. I really cannot comprehend why the clone makers skimp on these. Even in the US, in reel (e.g. 4K pcs) qty, a 47uF MLCC is about $0.20/ea. That means the difference of probably about $0.50 for the whole PCB. The other advantage of MLCCs is that they more or less last forever, whereas electrolytic caps will eventually dry out and fail (and who knows how old the ones you’re getting are and what the quality is to begin with).
In the upper right hand corner, you’ll see some footprints that weren’t solder pasted during stencil printing. To me, this is a good thing. You know what parts were intended to be populated and which were not. You also get a chance to examine the ENIG finish.
In the next photo, you’ll see the MPC5200 board. This is an 8 layer PCB.
There are a couple of things of note on this board:
(1) The AMD 10/100 ethernet PHY that’s used comes in 2 revisions and a few different temperature ratings. I have to check the details carefully between the rev A and B, but in terms of temp rating, this should be ‘I’ (industrial) vs ‘C’ (commercial).
These PHYs are ancient now, so any price difference should be minimal between the C and I version. Thus, again, I can’t imagine why anyone would try to save $0.01 and use the C version.
(2)(Anturage corrected me here — this header brings out USB, MII (Ethernet MAC), and some other signals)
(Will update below with the location of JTAG when I find it…)
The header at the lower left hand corner of the board is the JTAG header for the MPC5200. For PowerPC, they refer to this interface as BDM. I haven’t seen anyone talking about it on here, but this could be quite useful in some cases if/when the SDC is flaking out. For anyone who’s not familiar with this interface, it allows you to halt/breakpoint/single step the processor. You can also test the memory attached to the CPU etc. Unfortunately, on this MB Star Diagnosis SD Connect C4 particular PCB, some solder paste leaked through (although I’m not exactly sure how this could happen if I think about it…) onto a few of the pads.
(3) The memory chips are at the bottom. They’re DDR SDRAM (I made a mistake when I originally posted this, I wrote that they were not DDR, but upon closer inspection, they are). You can see the series termination resistors between the memory chips and the MPC5200. As others have pointed out, these should be identical and from the same date/lot code. These parts are plentiful and cheap as dirt, so there’s absolutely no excuse for any funny business there.
(4) The Spansion S29GL064N is a 64Mb (8MB) parallel NOR flash. Pretty standard for the time this unit was designed. This is what the MPC5200 boots from and where U-Boot, the RTOS, etc. live. You can dump and rewrite the contents of this flash via JTAG (mentioned above). These parts are still readily available and cheap.
You’ll notice on this MB Star C4 SD Connect PCB that right below the AMD PHY, there’s a 32KHz tuning fork crystal in a 4 pin package. This is the package that should have been used on the other PCB as well.
In general, this particular MB Star C4 SD Connect PCB looks to be of reasonably high quality.
The last photo that I have is of the LCD display.
I’ve seen a lot of different variants of this particular board.
There’s this example ‘FT-C4-LCD’. I’ve seen another ‘LCD V1.1’ variant as well.
The biggest thing with this board is that it’s a HASL (hot air solder level) finish. Granted, this is not the most complex PCB in the world by a long stretch, but it just goes to show you how for these companies will go to save every last penny. Although I haven’t seen the back side of one of the ‘FT-C4-LCD’ variants, the ‘LCD v1.1’ variant seems to use some ST microcontroller. Maybe the FT-C4-LCD has one on the back?
There’s nothing else particularly remarkable about this board, although my impression is that the higher quality units seem to use this FT-C4-LCD variant. If anyone has information to the contrary, I’d certainly appreciate knowing about it.
So as I’ve mentioned before, I’ve been sending these photos to any prospective sellers with MB Star C4 Mercedes Benz SD C4 units and asking them to address the issues I’ve pointed out here in writing.
If they either can’t or won’t, I just simply move on. I’m sure there are some people that will argue that I’m just wasting my time, but that’s fine, it’s my time to waste. I think if enough buyers start insisting on better quality up front, and stop buying garbage, it may encourage the factories to improve their quality in general.
To that end, I’m asking any seller each as eobdtool.com to guarantee, in writing, that I will receive exactly what we agreed upon up front, or that they will have to provide a full refund and pay return shipping. To be fair, I am willing to pay more for that. I’m not asking for a top shelf unit at a rock bottom price.
So for any sellers reading this that are interested, please post a note on here, as it may be of interest to others. No need to PM me. Any experience that I have with any seller, I will report back to on here fairly and accurately. I think anyone deserves a fair chance. At the same time, I will be completely honest and detailed about the entire experience, so please bear that in mind ahead of time. I would encourage others to do the same. I feel like this is one place where open communication will benefit everyone.
To any sellers that might be reading this:
Please understand that none of us want to buy a unit, have problems, and have to deal with sending back to China and playing games with you. All anyone wants is a high quality unit that will work reliably for years. It is better for you and for us to pay a little more up front and get a better quality product. Since you go to great lengths to obscure your production sources, it becomes your job to communicate to them that poor quality is not acceptable.
Any customer need good MB Star Diagnosis Tool MB Star C4 SD Connect Multiplexer SD C4 with guarantee, just contact us freely.
There are so many kinds MB Star C4 SD Connect Multiplexer in the market, how to choose a good Star Diagnosis SD Connect Multiplexer? Below Autonumen.com share a Star Diagnostic SD Connect MB Star C4 Mux identify guide as following. This is sharing from MHHAuto forum, great Mercedes Star diagnostic SDconnect SD C4 tools experience sharing.
MHHAuto Thread: SD Connect C4 — avoiding garbage
I’m in the market for an SD connect C4 mercedes benz Star Diagnostic Tool and have been trying to spend my time doing some homework to avoid getting a garbage unit. I certainly can understand what a lot of people have been saying about the widely varying quality that’s out there. I am a EE and PCB designer, so I’m trying to make use of that knowledge to select the best unit that I can.
To that end, I’m going to share what info I’ve collected so far, and when I finally end up buying whatever unit I do, I’m going to do a full teardown on it and post the results here.
As another matter, I’ll openly post details on who I buy the unit from and impressions after receiving it.
Near as I can tell right now, there appear to be about 4 “factories” that make different units.
One thing I’ve been asking all of the sellers for (and I would encourage others to do the same) is photos of the actual MB Star C4 SD Connect unit (including PCBs) with a unique identifier in the photo to prove that the unit they say they are going to send me is the actual one they send me. Of course, some sellers immediately bail at this, but then you know who to avoid ahead of time.
In general, a lot of the components used in a Star diagnostic tool SD C4 Multiplexer are getting quite long in the tooth. Many of the parts are approaching 20 years of age. Thus, you stand a fair risk of getting pulls (used parts) and/or remarked parts on these.
In following posts, I’ll provide photos of what I can discern as differences between the MB Star Diagnostic SD Connect C4 units along with some commentary about whatever info I can provide at this point.
to, I’ve outlined some things I feel are important to note. They have a set of 4 analog switches on the PCB. In this photo, they are ADG426 from Analog Devices. I’ve seen some clones that use DG526CY from Harris/Intersil. The DG526CY, besides being completely obsolete, has an typical RDSON of 270 ohms vs 80 for the Analog Devices part. It also has a -55dB isolation vs -75dB for the AD part. In short, the AD part is just a much better mux. So with that said, I would insist on any unit I’m interested in using those.
A second thing you’ll notice is the use of can crystals where 4 pin variants were intended. This is just sloppy and cheap. There may also be issue with loading (and ultimately clock stability) depending on whether they matched the loading caps to the substituted crystal or not.
I haven’t had a set of photos high res enough to look at the rest of the actives in detail yet, as most sellers don’t seem to post them.
There’s also an issue pointed out on the bottom of the board where one of the (what appears to be) MOSFETs in (what appears to be a) D2 PAK looks like it was hand soldered. Again, no good.
This next photo is of the relay Star Diagnosis SD Connect PCB— I think one of the MHH members posted this from an original SD C4.
.5NU relays and EPCOS S513N chokes. I’ve seen plenty of PCBs where they remove the chokes and stub them out with 0 ohm resistors. That is a high crime in terms of signal integrity. You see a lot of “full chips” comments where these are present, although that is a bit of a misnomer. It should read as “common mode filters present”.
On this PCB, you’ll also notice the use of multilayer ceramic capacitors (MLCC) near the switching supplies. A lot of clones seem to use electrolytic capacitors in place of the bigger MLCCs because of the cost. MLCCs are preferred for switchers because of their low ESR. I really cannot comprehend why the clone makers skimp on these. Even in the US, in reel (e.g. 4K pcs) qty, a 47uF MLCC is about $0.20/ea. That means the difference of probably about $0.50 for the whole PCB. The other advantage of MLCCs is that they more or less last forever, whereas electrolytic caps will eventually dry out and fail (and who knows how old the ones you’re getting are and what the quality is to begin with).
In the upper right hand corner, you’ll see some footprints that weren’t solder pasted during stencil printing. To me, this is a good thing. You know what parts were intended to be populated and which were not. You also get a chance to examine the ENIG finish.
In the next photo, you’ll see the MPC5200 board. This is an 8 layer PCB.
There are a couple of things of note on this board:
(1) The AMD 10/100 ethernet PHY that’s used comes in 2 revisions and a few different temperature ratings. I have to check the details carefully between the rev A and B, but in terms of temp rating, this should be ‘I’ (industrial) vs ‘C’ (commercial).
These PHYs are ancient now, so any price difference should be minimal between the C and I version. Thus, again, I can’t imagine why anyone would try to save $0.01 and use the C version.
(2)(Anturage corrected me here — this header brings out USB, MII (Ethernet MAC), and some other signals)
(Will update below with the location of JTAG when I find it…)
The header at the lower left hand corner of the board is the JTAG header for the MPC5200. For PowerPC, they refer to this interface as BDM. I haven’t seen anyone talking about it on here, but this could be quite useful in some cases if/when the SDC is flaking out. For anyone who’s not familiar with this interface, it allows you to halt/breakpoint/single step the processor. You can also test the memory attached to the CPU etc. Unfortunately, on this MB Star Diagnosis SD Connect C4 particular PCB, some solder paste leaked through (although I’m not exactly sure how this could happen if I think about it…) onto a few of the pads.
(3) The memory chips are at the bottom. They’re DDR SDRAM (I made a mistake when I originally posted this, I wrote that they were not DDR, but upon closer inspection, they are). You can see the series termination resistors between the memory chips and the MPC5200. As others have pointed out, these should be identical and from the same date/lot code. These parts are plentiful and cheap as dirt, so there’s absolutely no excuse for any funny business there.
(4) The Spansion S29GL064N is a 64Mb (8MB) parallel NOR flash. Pretty standard for the time this unit was designed. This is what the MPC5200 boots from and where U-Boot, the RTOS, etc. live. You can dump and rewrite the contents of this flash via JTAG (mentioned above). These parts are still readily available and cheap.
You’ll notice on this MB Star C4 SD Connect PCB that right below the AMD PHY, there’s a 32KHz tuning fork crystal in a 4 pin package. This is the package that should have been used on the other PCB as well.
In general, this particular MB Star C4 SD Connect PCB looks to be of reasonably high quality.
The last photo that I have is of the LCD display.
I’ve seen a lot of different variants of this particular board.
There’s this example ‘FT-C4-LCD’. I’ve seen another ‘LCD V1.1’ variant as well.
The biggest thing with this board is that it’s a HASL (hot air solder level) finish. Granted, this is not the most complex PCB in the world by a long stretch, but it just goes to show you how for these companies will go to save every last penny. Although I haven’t seen the back side of one of the ‘FT-C4-LCD’ variants, the ‘LCD v1.1’ variant seems to use some ST microcontroller. Maybe the FT-C4-LCD has one on the back?
There’s nothing else particularly remarkable about this board, although my impression is that the higher quality units seem to use this FT-C4-LCD variant. If anyone has information to the contrary, I’d certainly appreciate knowing about it.
So as I’ve mentioned before, I’ve been sending these photos to any prospective sellers with MB Star C4 Mercedes Benz SD C4 units and asking them to address the issues I’ve pointed out here in writing.
If they either can’t or won’t, I just simply move on. I’m sure there are some people that will argue that I’m just wasting my time, but that’s fine, it’s my time to waste. I think if enough buyers start insisting on better quality up front, and stop buying garbage, it may encourage the factories to improve their quality in general.
To that end, I’m asking any seller each as eobdtool.com to guarantee, in writing, that I will receive exactly what we agreed upon up front, or that they will have to provide a full refund and pay return shipping. To be fair, I am willing to pay more for that. I’m not asking for a top shelf unit at a rock bottom price.
So for any sellers reading this that are interested, please post a note on here, as it may be of interest to others. No need to PM me. Any experience that I have with any seller, I will report back to on here fairly and accurately. I think anyone deserves a fair chance. At the same time, I will be completely honest and detailed about the entire experience, so please bear that in mind ahead of time. I would encourage others to do the same. I feel like this is one place where open communication will benefit everyone.
To any sellers that might be reading this:
Please understand that none of us want to buy a unit, have problems, and have to deal with sending back to China and playing games with you. All anyone wants is a high quality unit that will work reliably for years. It is better for you and for us to pay a little more up front and get a better quality product. Since you go to great lengths to obscure your production sources, it becomes your job to communicate to them that poor quality is not acceptable.
Any customer need good MB Star Diagnosis Tool MB Star C4 SD Connect Multiplexer SD C4 with guarantee, just contact us freely.
Wednesday, July 24, 2019
How to update Benz MB SD Connect C4 firmware to 2.30
If the Mercedes Benz MB SD Connect C4 diagnostic
system reports “DCDI-eErrorCode=204 (204)” error, the possible reason
is that the SD Connect Star diagnosis firmware program was deleted so
that the Star multiplexer WIFI and configuration are failed. The only
solution is to update and flash the firmware. Error screenshots taken
below:
Follow the instruction here to updare the MB SD Connect C4 multiplexer firmware:
Update Star diagnosis Connect main unit firmware to 2.30 version:
1) Prepare 6 AA5 batteries, follow the pdf document “How to install MB SD C4 rechargeable battery” to installed battery
https://www.autonumen.com/category-163-b0-MB+Star+Compact+C4.html
NOTE: Must use the new battery and make sure battery is fully charged, otherwise may fail to update the firmware. Connect the Star diagnostic Connect multiplexer with computer via LAN cable and connect it with vehicle using OBD main cable. If SD C4 cannot connect to vehicle, feed it with OBD 12V power supply. If SD Connect is not connected with vehicle or fed with OBD 12V power supply, the SD Connect will report 622 firmware update fail error.
2) Open 2012.09 DAS software, browse to C:/program files/SDconnect Toolkit, to check if the three files are included in the folder: Update-automatic, Update-manual, Update-Special, shown as picture below:
If the file names are incorrect, rename the file.
3) Reboot the computer
4) Start updating firmware. Follow the instruction on “2 Update SDconnect”
https://mega.co.nz/#!PpMnSARa!BCD8S0Dv-9GWYR3OnzQp_TTZZG7zmtE1yBmxmVxsHxI
Follow the instruction here to updare the MB SD Connect C4 multiplexer firmware:
Update Star diagnosis Connect main unit firmware to 2.30 version:
1) Prepare 6 AA5 batteries, follow the pdf document “How to install MB SD C4 rechargeable battery” to installed battery
https://www.autonumen.com/category-163-b0-MB+Star+Compact+C4.html
NOTE: Must use the new battery and make sure battery is fully charged, otherwise may fail to update the firmware. Connect the Star diagnostic Connect multiplexer with computer via LAN cable and connect it with vehicle using OBD main cable. If SD C4 cannot connect to vehicle, feed it with OBD 12V power supply. If SD Connect is not connected with vehicle or fed with OBD 12V power supply, the SD Connect will report 622 firmware update fail error.
2) Open 2012.09 DAS software, browse to C:/program files/SDconnect Toolkit, to check if the three files are included in the folder: Update-automatic, Update-manual, Update-Special, shown as picture below:
If the file names are incorrect, rename the file.
3) Reboot the computer
4) Start updating firmware. Follow the instruction on “2 Update SDconnect”
https://mega.co.nz/#!PpMnSARa!BCD8S0Dv-9GWYR3OnzQp_TTZZG7zmtE1yBmxmVxsHxI
Tuesday, July 16, 2019
Mercedes BENZ C5 SD Connect Xentry Tab Kit Technical Support
Why MB Star Diagnostic tool is so well-received by thousands of
users, its technology and quality is developed after lots of experiments
and improvement. Recently, autonumen.com provide a new Star diagnosis
bundle, Mercedes BENZ C5 SD Connect Xentry Tab Kit( Newest Mercedes BENZ
Diagnostic Tool;Original second hand Mercedes BENZ C5 SD Connect Xentry
Tab Kit;With original software and tablet kit;Support BENZ latest
protocol)
BENZ C5 SD Connect Diagnostic Tool Description:
Mercedes Benz C5 Xentry Connect diagnostic interface, produced by French ACTIA Company and equipped with Panasonic Xentry-Tab, can test Engine / Transmission / air conditioning /SRS/ABS/ anti-theft system and OBD-II system.
Benz C5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
BENZ C5 SD Connect Diagnostic Tool Feature:
Efficient diagnostic program and complete vehicle database
Simple and easy-to-use user interface (UI)
High-performance Tab with 4G memory and 13.3 inch LCD touch screen
Advanced upgraded VCI+ communication inter
Support Wired/ wireless connection
Cover all new Mercedes Benz models.
BENZ C5 SD Connect Diagnostic Tool Configuration parameters
A full set of kit configuration
1.Panasonic newest widescreen tab.
2.The original Xentry-Connect by ACTIA
3.Mercedes Benz OBD2 diagnostic cable
Panasonic widescreen Xentry-Tab technical parameters:
OS: windows 7
ultimate CPU:4G
Hard disk memory: 250G
13.3inch touch screen
Xentry-Connect (VCI+) Technical Parameters:
OS: Windows Embedded Standard 7(32bit)
Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
Memory: 4G hard disk with 256GB SSD
Display: 128*64 PX
Battery: 40 minutes (When CPU capacity to 60%)
Weight: 1.9KG
Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
BENZ C5 SD Connect Diagnostic Tool Description:
Mercedes Benz C5 Xentry Connect diagnostic interface, produced by French ACTIA Company and equipped with Panasonic Xentry-Tab, can test Engine / Transmission / air conditioning /SRS/ABS/ anti-theft system and OBD-II system.
Benz C5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
BENZ C5 SD Connect Diagnostic Tool Feature:
Efficient diagnostic program and complete vehicle database
Simple and easy-to-use user interface (UI)
High-performance Tab with 4G memory and 13.3 inch LCD touch screen
Advanced upgraded VCI+ communication inter
Support Wired/ wireless connection
Cover all new Mercedes Benz models.
BENZ C5 SD Connect Diagnostic Tool Configuration parameters
A full set of kit configuration
1.Panasonic newest widescreen tab.
2.The original Xentry-Connect by ACTIA
3.Mercedes Benz OBD2 diagnostic cable
Panasonic widescreen Xentry-Tab technical parameters:
OS: windows 7
ultimate CPU:4G
Hard disk memory: 250G
13.3inch touch screen
Xentry-Connect (VCI+) Technical Parameters:
OS: Windows Embedded Standard 7(32bit)
Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
Memory: 4G hard disk with 256GB SSD
Display: 128*64 PX
Battery: 40 minutes (When CPU capacity to 60%)
Weight: 1.9KG
Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
Wednesday, July 10, 2019
Mercedes Benz star C3/C4/C5 buying guide
Mercedes benz star scanner is a very
popular auto scanner in the market. However,Many customer are confused
to choose when they want to buy one, because there is four version of mb
star:Mercedes Benz star c3,benz star c4, Benz Star SD Connect Compact 4
C4 and super MB benz star C5.
So now,i will summarize their similarity and difference,hope it will helpful for customers to choose.Similarity:
1.Benz star C3/C4 and MB star sd connect c4,Super MB Star c5 use same software.
2.For the hardware, Benz star C3/C4/C5 is same function in diagnosing.
Difference:
1.For the functions, MB star c3 and c4 are almost the same,C4 can do all the works what C3 does and it is the replacement of Compact C3.
Just benz star c4 size is small and weight is light,much convience and the anti‐interrupting ability is better.
One more thing, as customer feedback, the advantage of c3 is can do trucks best.
2.MB starC3, C4 just can support Mercedes Benz cars manufactured after year 2000. Super MB star c5,Benz SD Connect C4 can support all current and new coming MB vehicles.
3.Benz star c3,c4,SD connect C4 update by Harddisk.That means when customer want to update,they need to send back harddisk to supplier,after finish update,then send back to them again or just buy a new HDD.For the long international distance,it may need about 2 weeks can complete one time update,so it is very trouble and inconvience.
Under this suitation,Super mb benz star c5 is release, it is can update through super mb star official web directly, which will be much convience and time saving.
In addition,Super mb star C5 work with W204, W207, W212, 405, 451, 452 and 454. Besides the software c3 and c4 own,it added three more software: SD Media, Xentry and Smart TAN Code.
SD Media: Video and PDF lessons;
Xentry:New software released by Benz Company after 04/2009 by diagnosis new cars. Xentry software for diagnosing W 204,W207 and W212 which C3 and C4 does not support;
Smart TAN Code: Opened special function in DAS program with Smart cars 405/ 451/452/ 454.Besides, it also opened more special functions, such as engineer mode, remove limitations,etc, which Star C3 and Star C4 do not have.
4.Now we turn to MB star SD connect C4 again.MB Star SD connect C4 not only support KL diagnosis and three lines CAN BUS diagnosis, but also support UDS diagnose protocol, Because it have UDS chips. Star C3,C4,c5 don’t have this chip, so they can not support UDS.
The most advantage of SD connect c4 is: It can connect to PC by wireless or Lan cable.So it will be much more convience than Benz star C3/C4/c5.
Besides, Mercedes Benz star SD connect C4 interface components used the military quickly inserted techniques that can support one million times plug, more stably;And all of the its core components adopt new original packaged chip, plus 24 hours fatigue test, to ensure its stable release.
So in all,each version have its advantage,just see which one is most suitable and interested you.
Wednesday, July 3, 2019
V2017.9 Original Software Mercedes Benz MB SD C5 SD Connect Compact 5 Star Diagnosis with Engineer
Benz c5 can provide complete diagnosis for the newest hybrid
W222. And it has a qualitative improvement in hardware and software by
authorization of diagnostic interface to control the software.can work
on windows xp, win7/8/10 system.
Xentry Connect C5 Benz SD Connect DoIP Wifi MB Star C5 Xentry Tab Kit Diagnosis Multiplexer
Benz c5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
The tool we sell do not include the xentry tab, you can equip one yourself or choose other laptop, it is just as a display, no special requirement.
Xentry Connect (VCI+) Technical Parameters:
1.OS: Windows Embedded Standard 7(32bit)
2.Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
3.Memory: 4G hard disk with 256GB SSD
4.Display: 128*64 PX
5.Battery: 40 minutes (When CPU capacity to 60%)
6.Weight: 1.9KG
7.Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
The way to connect: support wireless connection via 1000M workshop switches, also support wired connection.
What the difference on diagnostic systems based on Xentry Connect from other equipment used to diagnose Mercedes cars?
What are its distinguishing features?
Hardware, despite the similarity of many solutions with multiplexers SD Connect –
but the different All diagnostic software is loaded into the Xentry Connect multiplexer itself.
The management software can be installed on any computer with Windows 7 – 32-bit or Windows 8 – 32-bit and serves only for communication with the multiplexer
The licensing system is reworked – now licenses are stored on MB servers – Any license changes are tracked by the multiplexer when connected to the Internet network.
Why should buy Xentry connect
After 2015, all Star Diagnosis equipment is no longer supported. First of all, this means that there is no update of the diagnostic data for the newest cars and their systems, as well as the lack of the possibility of coding and programming of electronic units due to the backlog of the software data level in the device, from data in the electronic control units of the car.
Already at the end of 2014, at most dealerships, almost all of the previously used Star Diagnosis Compact4 with SD Connect DoIP multiplexers were almost completely removed. Instead, dealers received Xentry Kit kits, which include the latest Xentry Connect multiplexers and Xentry Tab tablets from Panasonic. Tablets are custom-made, although they also have a “civilian” version – the Panasonic Toughbook CF-D1,
somewhat inferior in terms of battery life to the original Xentry Tab, but it has a much more powerful configuration.
Honestly, the need to use the Xentry Tab on non-dealer services seems somewhat exaggerated to me. With dealers everything is clear – they were forced to use this equipment.
And what about workshop service? Undoubtedly, the tablet from Panasonic is not very bad … But … Its price is disheartening. The cost of the Japanese tablet is realistic to buy pieces of eight new laptops or tablets from other manufacturers.
So , we suggest buy Xentry connect from us , then buy a laptop yourself . the software from which Xentry Connect is managed can be installed without any problems on any computer that has a 32-bit version of Windows 7, Windows 8 or Windows 10. It’s clear with Xentry Connect itself – there’s no alternative .
After all, in this choice there are many reasons that encourage one to make a decision. The main thing is one: since 2015, the diagnostic multiplexer Xentry Connect C5 becomes the only one used at dealerships.
Thus, by purchasing this equipment, you do not lag behind the progress. You use in your work the best that is available today. Each your client, seeing with his own eyes that you in your work use the same device that he saw at the dealer’s service station, will understand that he made the right decision entrusting his car to your specialists.
Xentry Connect C5 Benz SD Connect DoIP Wifi MB Star C5 Xentry Tab Kit Diagnosis Multiplexer
Benz c5 can provide complete diagnosis for the newest hybrid W222. And it has a qualitative improvement in hardware and software by authorization of diagnostic interface to control the software.
The tool we sell do not include the xentry tab, you can equip one yourself or choose other laptop, it is just as a display, no special requirement.
Xentry Connect (VCI+) Technical Parameters:
1.OS: Windows Embedded Standard 7(32bit)
2.Processor: ArrandaieCeleron P4500 oder P4505(38W TDP)
3.Memory: 4G hard disk with 256GB SSD
4.Display: 128*64 PX
5.Battery: 40 minutes (When CPU capacity to 60%)
6.Weight: 1.9KG
7.Network connection: WLAN : IEEE802.11 a/b/g/n2.4+5GHZ
The way to connect: support wireless connection via 1000M workshop switches, also support wired connection.
What the difference on diagnostic systems based on Xentry Connect from other equipment used to diagnose Mercedes cars?
What are its distinguishing features?
Hardware, despite the similarity of many solutions with multiplexers SD Connect –
but the different All diagnostic software is loaded into the Xentry Connect multiplexer itself.
The management software can be installed on any computer with Windows 7 – 32-bit or Windows 8 – 32-bit and serves only for communication with the multiplexer
The licensing system is reworked – now licenses are stored on MB servers – Any license changes are tracked by the multiplexer when connected to the Internet network.
Why should buy Xentry connect
After 2015, all Star Diagnosis equipment is no longer supported. First of all, this means that there is no update of the diagnostic data for the newest cars and their systems, as well as the lack of the possibility of coding and programming of electronic units due to the backlog of the software data level in the device, from data in the electronic control units of the car.
Already at the end of 2014, at most dealerships, almost all of the previously used Star Diagnosis Compact4 with SD Connect DoIP multiplexers were almost completely removed. Instead, dealers received Xentry Kit kits, which include the latest Xentry Connect multiplexers and Xentry Tab tablets from Panasonic. Tablets are custom-made, although they also have a “civilian” version – the Panasonic Toughbook CF-D1,
somewhat inferior in terms of battery life to the original Xentry Tab, but it has a much more powerful configuration.
Honestly, the need to use the Xentry Tab on non-dealer services seems somewhat exaggerated to me. With dealers everything is clear – they were forced to use this equipment.
And what about workshop service? Undoubtedly, the tablet from Panasonic is not very bad … But … Its price is disheartening. The cost of the Japanese tablet is realistic to buy pieces of eight new laptops or tablets from other manufacturers.
So , we suggest buy Xentry connect from us , then buy a laptop yourself . the software from which Xentry Connect is managed can be installed without any problems on any computer that has a 32-bit version of Windows 7, Windows 8 or Windows 10. It’s clear with Xentry Connect itself – there’s no alternative .
After all, in this choice there are many reasons that encourage one to make a decision. The main thing is one: since 2015, the diagnostic multiplexer Xentry Connect C5 becomes the only one used at dealerships.
Thus, by purchasing this equipment, you do not lag behind the progress. You use in your work the best that is available today. Each your client, seeing with his own eyes that you in your work use the same device that he saw at the dealer’s service station, will understand that he made the right decision entrusting his car to your specialists.
Wednesday, May 29, 2019
Really helpful guide to buy a MB Star diagnostic system
Really helpful guide to buy a MB Star diagnostic system
I can help you out with getting a MB Star Diagnostic system.
I have a lot of experience with setting up these systems.
The C4 (MB SD Connect C4) units are nice because of the LAN cable connecting the unit to the laptop, as with high quality electronics there seem to be no problems with these units.
I do prefer the MB Star C3 units just because they seem to hold up much better than the MB SD C4’s. The only downside to the C3 multiplexer is the requirement of a serial port on the laptop and the big bulky cable that goes from the head to the laptop.
Software:
Many of the chinese setups you see that sell you a hard drive and “will work with any laptop” are just VM ware installations. Basically a virtual windows setup.. There is no reason to go this route, they are prone to crashing and much slower than native (software installed strait into windows) setups.
There are many different versions of the MB Star diagnostic software and each have their up’s and downs. You can get the 2014 software that will work with cars just being pulled off the ships. But most people wont be working on the latest cars so I always suggest older versions from 2010 to 2012. As the software keeps being updated by Mercedes they remove more and more features limiting what you can do as far as basic programming goes as well as other small things here and there..
You can be able to SCN code control units with one of these setups. Mercedes has everything setup to connect to their internet databases for verification to do SCN coding and requires a license you need to purchase.. It is technically possible to do, but for most independent shops its not worth the cost. Basic coding/programming of control units can be done with these systems, but like I said you cant do everything..
Of course these systems do all your basic reading erasing of codes, they have guided troubleshooting in them as well. You can actuate components and read data outputs.
Im sure you get the picture by now.. These can be setup on pretty much any laptop you want with some limitations. SSD drives or just normal hard drives.. makes no difference when you are doing everything from scratch like I do..
If your interested in purchasing a system feel free to contact autonumen.com. They will answer any questions you might have and can figure out exactly what kind of setup you want. They also provide a 1 year warranty on all my systems, which is something you don’t really get when your faced with shipping a package back to china and hoping that all works out.
I can help you out with getting a MB Star Diagnostic system.
I have a lot of experience with setting up these systems.
The C4 (MB SD Connect C4) units are nice because of the LAN cable connecting the unit to the laptop, as with high quality electronics there seem to be no problems with these units.
I do prefer the MB Star C3 units just because they seem to hold up much better than the MB SD C4’s. The only downside to the C3 multiplexer is the requirement of a serial port on the laptop and the big bulky cable that goes from the head to the laptop.
Software:
Many of the chinese setups you see that sell you a hard drive and “will work with any laptop” are just VM ware installations. Basically a virtual windows setup.. There is no reason to go this route, they are prone to crashing and much slower than native (software installed strait into windows) setups.
There are many different versions of the MB Star diagnostic software and each have their up’s and downs. You can get the 2014 software that will work with cars just being pulled off the ships. But most people wont be working on the latest cars so I always suggest older versions from 2010 to 2012. As the software keeps being updated by Mercedes they remove more and more features limiting what you can do as far as basic programming goes as well as other small things here and there..
You can be able to SCN code control units with one of these setups. Mercedes has everything setup to connect to their internet databases for verification to do SCN coding and requires a license you need to purchase.. It is technically possible to do, but for most independent shops its not worth the cost. Basic coding/programming of control units can be done with these systems, but like I said you cant do everything..
Of course these systems do all your basic reading erasing of codes, they have guided troubleshooting in them as well. You can actuate components and read data outputs.
Im sure you get the picture by now.. These can be setup on pretty much any laptop you want with some limitations. SSD drives or just normal hard drives.. makes no difference when you are doing everything from scratch like I do..
If your interested in purchasing a system feel free to contact autonumen.com. They will answer any questions you might have and can figure out exactly what kind of setup you want. They also provide a 1 year warranty on all my systems, which is something you don’t really get when your faced with shipping a package back to china and hoping that all works out.
Monday, May 13, 2019
Home Launch X431 BMW ICOM Mb Star Autoboss Tools (SPX) AUTOCOM CDP T300 CK100 CRP123 Easy methods to select MB Star, Extremely MB Star, MB SD C4, Mercedes BENZ C5 SD Home Easy methods to select MB Star, Extremely MB Star, MB SD C4, Mercedes BENZ C5 SD Easy methods to select MB Star, Extremely MB Star, MB SD C4, Mercedes BENZ C5 SD
MB Star, Extremely MB SD Connect C4, MB SD C4, Mercedes BENZ C5 SD are usually analysis tools to get benz, and autonumen.com have several different benz diagnostic tools,how to choose from them?
you. HDD Practice Hints:
you. Work with outside HDD, you should ensure you in close proximity a person’s anti-virus program as soon as going your program, in any other case program will be broken couple of. If you are using inside HDD similar to DELL D630 HDD, you should do not install new softare upon our own hard disk, furthermore you should do not adjust our own program, should program happen to be broken.
a few. In the event you build your password to get our own program, you should don’t forget your password. couple of. Star analysis tools assist encoding operate, include online& real world encoding, what you need to be charged focus?
you. To get online encoding operate, 2014. 12 and more sophisticated program could assist. To get old edition, can not assist.
couple of. Whenever purchaser needs to open up your real world operate, program edition in advance of 2014. 07 can not assist.
a few. Benz star c3, c4, plenty of motor vehicle styles would possibly not assist online encoding. Far better to decide on mb sd c4 having most recent 2015. 07 program.
a few. MB Star, Extremely MB Star, MB SD C4, Mercedes BENZ C5 SD Hook up Comparing:
Object NO. SP45-C SP45-F SP117 SP06 SP100-B SP100-D SP45-B SP243
Object Name MB Star C3 MB Star C3
having 7 cables Best MB Star C3 MB Star C4 MB SD C4 MB SD C4 Super MB STAR C3 Second Hands MB SD C5
Original NO NO NO NO NO NO HDD is definitely original Original
Most recent Version 2015. 05 2015. 05 2015. 07 2015. 05 2015. 07 2015. 07 2015. 05
Update By HDD By HDD By HDD By HDD By HDD By HDD Update Online
12 months to get free Support Redesign
Tough Disk External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
T30 HDD,
Dell D630 HDD SSD HDD
Assist
Vehicles 12V automobiles only cars, trucks cars, trucks cars, trucks cars, trucks cars, trucks cars, trucks cars, vans
Connection Cable Connection Cable Connection Cable Connection Cable Connection Lan Wire and
Cellular Connection Lan Wire and
Cellular Connection Cable Connection Cable Link
Cellular Link
Protocols K-line and
COULD Bus K-line and
COULD Bus K-line and
COULD Bus K-line and
COULD Bus k-line, COULD Bus,
UDS k-line, COULD Bus,
UDS K-line and
COULD Bus Support BENZ most recent process
Assist Most recent Crossbreed W222.
you. HDD Practice Hints:
you. Work with outside HDD, you should ensure you in close proximity a person’s anti-virus program as soon as going your program, in any other case program will be broken couple of. If you are using inside HDD similar to DELL D630 HDD, you should do not install new softare upon our own hard disk, furthermore you should do not adjust our own program, should program happen to be broken.
a few. In the event you build your password to get our own program, you should don’t forget your password. couple of. Star analysis tools assist encoding operate, include online& real world encoding, what you need to be charged focus?
you. To get online encoding operate, 2014. 12 and more sophisticated program could assist. To get old edition, can not assist.
couple of. Whenever purchaser needs to open up your real world operate, program edition in advance of 2014. 07 can not assist.
a few. Benz star c3, c4, plenty of motor vehicle styles would possibly not assist online encoding. Far better to decide on mb sd c4 having most recent 2015. 07 program.
a few. MB Star, Extremely MB Star, MB SD C4, Mercedes BENZ C5 SD Hook up Comparing:
Object NO. SP45-C SP45-F SP117 SP06 SP100-B SP100-D SP45-B SP243
Object Name MB Star C3 MB Star C3
having 7 cables Best MB Star C3 MB Star C4 MB SD C4 MB SD C4 Super MB STAR C3 Second Hands MB SD C5
Original NO NO NO NO NO NO HDD is definitely original Original
Most recent Version 2015. 05 2015. 05 2015. 07 2015. 05 2015. 07 2015. 07 2015. 05
Update By HDD By HDD By HDD By HDD By HDD By HDD Update Online
12 months to get free Support Redesign
Tough Disk External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
Dell D630 HDD External HDD,
T30 HDD,
Dell D630 HDD SSD HDD
Assist
Vehicles 12V automobiles only cars, trucks cars, trucks cars, trucks cars, trucks cars, trucks cars, trucks cars, vans
Connection Cable Connection Cable Connection Cable Connection Cable Connection Lan Wire and
Cellular Connection Lan Wire and
Cellular Connection Cable Connection Cable Link
Cellular Link
Protocols K-line and
COULD Bus K-line and
COULD Bus K-line and
COULD Bus K-line and
COULD Bus k-line, COULD Bus,
UDS k-line, COULD Bus,
UDS K-line and
COULD Bus Support BENZ most recent process
Assist Most recent Crossbreed W222.
Tuesday, March 19, 2019
Mercedes Benz C5 Xentry connect with Wifi MB Star SD Connect C5 multiplexer support mercedes scn coding online and offline functions
Mercedes Benz C5 Xentry connect with Wifi MB Star SD Connect C5 multiplexer support mercedes scn coding online and offline functions
Mercedes Benz C5 Xentry connect with Wifi update from MB Star SD Connect C4 Mux. Wifi MB Star SD Connect C5 multiplexer software update to V2017.5 Mercedes benz xentry das. Autonumen.com Mercedes Benz C5 Xentry connect with Wifi MB Star SD Connect C5 multiplexer support mercedes scn coding online and offline functions.
Wifi MB Star SD Connect C5 Mercedes Xentry Connect C5 Mux Benz Star diagnosis C5 multiplexer
c5 xentry connect
Mercedes Benz C5 Xentry connect with Wifi from Autonumen.com the newest and latest diagnostic tool for Mercedes Benz, it not only for cars, but also support trucks. the software version is 2016.07
Autonumen.com Wifi MB Star SD Connect C5 multiplexer Star Diagnosis support wireless diagnose, support multi-language such as English/Bulgarian/Danish/Greek/Spanish/French/Italian/Korean/Polish/Romanuan/Croatian Turkish/Czech/German/Finish/Hyngarian/Japanese/Dutch/Portuguese/Russian/Swedish/Chinese and more.
The Autonumen.com mb star c5 xentry connect support Offline and Online Programming, If You Want to Do Online, Please Buy This mercedes SCN Coding online Service. If want to do mercedes scn coding offline, you only need use the mercedes vediamo scn coding software, thanks.
For more details information, welcome to Add my Whatsapp (+86 15889512468) or Skype Autonumen.com) if you have, Your Private Secretary in Car Repair Area! 16 Hours Online at your Service!
Autonumen.com- China OBD2 Tuner Tool Automotive Diagnostic Tools Car Key Programmer OBD2 ECU chip tuning tool Center.
Focus On OBD Tool Since 2008
Wechat/WhatsApp:(+86)15815514521
Email:service@autonumen.com
Website:www.autonumen.com
Mercedes Benz C5 Xentry connect with Wifi update from MB Star SD Connect C4 Mux. Wifi MB Star SD Connect C5 multiplexer software update to V2017.5 Mercedes benz xentry das. Autonumen.com Mercedes Benz C5 Xentry connect with Wifi MB Star SD Connect C5 multiplexer support mercedes scn coding online and offline functions.
Wifi MB Star SD Connect C5 Mercedes Xentry Connect C5 Mux Benz Star diagnosis C5 multiplexer
c5 xentry connect
Mercedes Benz C5 Xentry connect with Wifi from Autonumen.com the newest and latest diagnostic tool for Mercedes Benz, it not only for cars, but also support trucks. the software version is 2016.07
Autonumen.com Wifi MB Star SD Connect C5 multiplexer Star Diagnosis support wireless diagnose, support multi-language such as English/Bulgarian/Danish/Greek/Spanish/French/Italian/Korean/Polish/Romanuan/Croatian Turkish/Czech/German/Finish/Hyngarian/Japanese/Dutch/Portuguese/Russian/Swedish/Chinese and more.
The Autonumen.com mb star c5 xentry connect support Offline and Online Programming, If You Want to Do Online, Please Buy This mercedes SCN Coding online Service. If want to do mercedes scn coding offline, you only need use the mercedes vediamo scn coding software, thanks.
For more details information, welcome to Add my Whatsapp (+86 15889512468) or Skype Autonumen.com) if you have, Your Private Secretary in Car Repair Area! 16 Hours Online at your Service!
Autonumen.com- China OBD2 Tuner Tool Automotive Diagnostic Tools Car Key Programmer OBD2 ECU chip tuning tool Center.
Focus On OBD Tool Since 2008
Wechat/WhatsApp:(+86)15815514521
Email:service@autonumen.com
Website:www.autonumen.com
Tuesday, March 5, 2019
How to Distinguish MB SD C4 and MB Star C4
MB SD C4 and MB Star C4 is hot Mercedes Benz MB Star Diagnostic tool,
while most customers will mixture them, especially buy newest update
software hdd,few customers notice the newest update software hdd they
bought is not compatible with their Benz Star diagnostic interface,
that’s unhappy.
Here we collect some information show you how to distinguish these two items from: supported protocols, communication method, available hard disk model and whether battery need
1. Supported protocols different
MB SD C4: k-line, CAN Bus, UDS protocols, can work on more new vehicles
MB Star C4: k-line, CAN Bus
2. Communication method:
MB SD C4: support both Lan cable and Wifi connection(with the wifi option, you do not need sit at the front of laptop for the test, and you can send the data to your laptop via wifi)
MB Star C4: support cable connection only
3. Available hard disk different
MB SD C4: External HDD,Dell D630 HDD(can not work on T30 Laptop)
MB Star C4: External HDD,Dell D630 HDD,T30 HDD to choose
4. Whether battery need
MB SD C4: Need install batteries(the battery specification: 6 Ni-MH Rechargeable batteries, Size: AA, Voltage: 1.2V, Capacity: above 1700Ma)
MB Star C4: powered by Vehicle’s 12 volt electrical system
Here we collect some information show you how to distinguish these two items from: supported protocols, communication method, available hard disk model and whether battery need
1. Supported protocols different
MB SD C4: k-line, CAN Bus, UDS protocols, can work on more new vehicles
MB Star C4: k-line, CAN Bus
2. Communication method:
MB SD C4: support both Lan cable and Wifi connection(with the wifi option, you do not need sit at the front of laptop for the test, and you can send the data to your laptop via wifi)
MB Star C4: support cable connection only
3. Available hard disk different
MB SD C4: External HDD,Dell D630 HDD(can not work on T30 Laptop)
MB Star C4: External HDD,Dell D630 HDD,T30 HDD to choose
4. Whether battery need
MB SD C4: Need install batteries(the battery specification: 6 Ni-MH Rechargeable batteries, Size: AA, Voltage: 1.2V, Capacity: above 1700Ma)
MB Star C4: powered by Vehicle’s 12 volt electrical system
Tuesday, February 26, 2019
Mercedes Benz star C3/C4/C5 buying guide
Mercedes benz star scanner is a very popular auto scanner in the
market. However,Many customer are confused to choose when they want to
buy one, because there is four version of mb star:Mercedes Benz star
c3,benz star c4, Benz Star SD Connect Compact 4 C4 and super MB benz star C5.
So now,i will summarize their similarity and difference,hope it will helpful for customers to choose.
Similarity:
1.Benz star C3/C4 and MB star sd connect c4,Super MB Star c5 use same software.
2.For the hardware, Benz star C3/C4/C5 is same function in diagnosing.
Difference:
1.For the functions, MB star c3 and c4 are almost the same,C4 can do all the works what C3 does and it is the replacement of Compact C3.
Just benz star c4 size is small and weight is light,much convience and the anti‐interrupting ability is better.
One more thing, as customer feedback, the advantage of c3 is can do trucks best.
2.MB starC3, C4 just can support Mercedes Benz cars manufactured after year 2000. Super MB star c5,Benz SD Connect C4 can support all current and new coming MB vehicles.
3.Benz star c3,c4,SD connect C4 update by Harddisk.That means when customer want to update,they need to send back harddisk to supplier,after finish update,then send back to them again or just buy a new HDD.For the long international distance,it may need about 2 weeks can complete one time update,so it is very trouble and inconvience.
Under this suitation,Super mb benz star c5 is release, it is can update through super mb star official web directly, which will be much convience and time saving.
In addition,Super mb star C5 work with W204, W207, W212, 405, 451, 452 and 454. Besides the software c3 and c4 own,it added three more software: SD Media, Xentry and Smart TAN Code.
SD Media: Video and PDF lessons;
Xentry:New software released by Benz Company after 04/2009 by diagnosis new cars. Xentry software for diagnosing W 204,W207 and W212 which C3 and C4 does not support;
Smart TAN Code: Opened special function in DAS program with Smart cars 405/ 451/452/ 454.Besides, it also opened more special functions, such as engineer mode, remove limitations,etc, which Star C3 and Star C4 do not have.
4.Now we turn to MB star SD connect C4 again.MB Star SD connect C4 not only support KL diagnosis and three lines CAN BUS diagnosis, but also support UDS diagnose protocol, Because it have UDS chips. Star C3,C4,c5 don’t have this chip, so they can not support UDS.
The most advantage of SD connect c4 is: It can connect to PC by wireless or Lan cable.So it will be much more convience than Benz star C3/C4/c5.
Besides, Professional Diagnostic Tools
So in all,each version have its advantage,just see which one is most suitable and interested you.
So now,i will summarize their similarity and difference,hope it will helpful for customers to choose.
Similarity:
1.Benz star C3/C4 and MB star sd connect c4,Super MB Star c5 use same software.
2.For the hardware, Benz star C3/C4/C5 is same function in diagnosing.
Difference:
1.For the functions, MB star c3 and c4 are almost the same,C4 can do all the works what C3 does and it is the replacement of Compact C3.
Just benz star c4 size is small and weight is light,much convience and the anti‐interrupting ability is better.
One more thing, as customer feedback, the advantage of c3 is can do trucks best.
2.MB starC3, C4 just can support Mercedes Benz cars manufactured after year 2000. Super MB star c5,Benz SD Connect C4 can support all current and new coming MB vehicles.
3.Benz star c3,c4,SD connect C4 update by Harddisk.That means when customer want to update,they need to send back harddisk to supplier,after finish update,then send back to them again or just buy a new HDD.For the long international distance,it may need about 2 weeks can complete one time update,so it is very trouble and inconvience.
Under this suitation,Super mb benz star c5 is release, it is can update through super mb star official web directly, which will be much convience and time saving.
In addition,Super mb star C5 work with W204, W207, W212, 405, 451, 452 and 454. Besides the software c3 and c4 own,it added three more software: SD Media, Xentry and Smart TAN Code.
SD Media: Video and PDF lessons;
Xentry:New software released by Benz Company after 04/2009 by diagnosis new cars. Xentry software for diagnosing W 204,W207 and W212 which C3 and C4 does not support;
Smart TAN Code: Opened special function in DAS program with Smart cars 405/ 451/452/ 454.Besides, it also opened more special functions, such as engineer mode, remove limitations,etc, which Star C3 and Star C4 do not have.
4.Now we turn to MB star SD connect C4 again.MB Star SD connect C4 not only support KL diagnosis and three lines CAN BUS diagnosis, but also support UDS diagnose protocol, Because it have UDS chips. Star C3,C4,c5 don’t have this chip, so they can not support UDS.
The most advantage of SD connect c4 is: It can connect to PC by wireless or Lan cable.So it will be much more convience than Benz star C3/C4/c5.
Besides, Professional Diagnostic Tools
So in all,each version have its advantage,just see which one is most suitable and interested you.
Subscribe to:
Posts (Atom)